Suggested Procedure for Gas Switching during Decompression Diving


(decompression diver and trimix classes)

During any staged decompression dive it is standard practice to switch from backgas to a more oxygen rich gas at least once during ascent. Because of the potential risks associated with breathing high partial pressures of oxygen, divers are strongly advised to adopt a set procedure for gas switching which includes standardized safety protocols. The following is a suggested procedure.

Step-by-step procedures

All scuba cylinders should be dedicated to standard decompression gases and be marked clearly according to Standards. In addition, decompression cylinders should be marked with actual Maximum Operating Depth (MOD) of contents with removable tape on two sides of cylinder valve. This MOD must be based on recent analysis and calculations for acceptable dose of partial pressure at that marked MOD and should show NOTHING but MOD in meters or feet clearly marked in large numbers. (See cylinder labeling procedures for full details.)

All decompression cylinders should be worn on diver’s left side with valve orifice facing diver and valve on/off knobs pointing to left. Divers enter water with regulator(s) on decompression cylinders charged and valve(s) closed.

During ascent, each diver will begin gas switch procedure prior to reaching switch depth (gas MOD). Deployment should follow the following steps.

Each team members “unstows” hose and second stage of selected decompression mix and pulls hose across her body with regulator second stage in right hand. Starting with dive leader, each members asks a buddy to “Look at my gas. Please confirm it is correct for next stop.” Buddy must follow hose to first stage, read actual MOD and confirm that the regulator will deliver the correct gas for the coming gas switch. This query / confirmation cycle will be done one diver at a time.

Divers will then follow schedule and proceed to MOD for gas switch. Once there, they will switch regulators and with left hand on cylinder valve will breathe hose dry while checking SPG on selected decompression gas. As reading drops, indicating once again that regulator is indeed connected to the correct cylinder, they will turn on the decompression valve allowing decompression gas to flow normally. Once they are sure regulator is breathing normally, they stow the backgas regulator they were formerly using. At the same time, each team member should indicate the status of their gas switch to dive leader. Once each team member has signaled “Switch went OK,” decompression at that depth will start.

This procedure is repeated for each gas switch made during the dive.

Some further thoughts and notes:

Do not breathe a gas which has not been analyzed by you or in your presence. There should be no exceptions to this rule.

It is imperative that all team members have similar decompression gases which can be switched within a depth of one meter or less.

Gas switching is perhaps the most stressful exercise performed during a normal ascent from a technical dive. It should never be executed in a cavalier or complacent way because the potential consequences of sloppy procedures are simply too severe. Second stage should be inspected for foreign matter before being breathed… muck, critters et al.

Whenever possible, use gases that all team members are familiar with such as EAN50, 50/25/25, pure Oxygen for decompression. However, when you are in the field and these “standard mixes” are NOT available, it is even more important (if that’s possible) that you follow the procedure outlined here!

Advertisements

One thought on “Suggested Procedure for Gas Switching during Decompression Diving

  1. hello I have question for you you may help me … i do deco diving for long time i never had a problem but for last few months im feeling tied after my dives i do deco as i should do i do not going up fast so i dont know what is going know the only thing i can think of is that i put some weight on me about 15-20 pounds do you think that that is the problem ? Thank you Stanley

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s